Chain, Jewelry Wire & Gemstones Earrings Jewelry Making Project -- Page 5

HOME   JEWELRY MAKING INSTRUCTIONS   WIGJIG UNIVERSITY   NEWSLETTER   GIFT IDEAS   WIGJIG STORE
VIEW OUR BEADS  BLING  BOOKS  CHAIN  FINDINGS  MISC  SUPPLIES  THREAD  JEWELRY TOOLS  WATCHES  WIRE

Chain, Jewelry Wire & Gemstones Earrings Jewelry Making Project:  1     2     3    4     5    6     7     8     9     10     11 
View our Free Jewelry Making Instructions     Jewelry Making Skills     Jewelry Making Supplies     Jewelry Making Tools

Step 20 to Chain, Jewelry Wire and Gemstones Earrings Jewelry Making ProjectStep 22:  Remove the wire from your jig.  Add peg 7 to the pattern and replace the wire on your jig with the initial loop on peg 7 with the remainder of the wire orientatedStep 23 to Chain, Jewelry Wire & Gemstone Earrings Jewelry Making Project as shown at right. 

Step 23:  Now wrap the wire around peg 4 as shown at left.  Continue pushing the wire until the wire tail rests adjacent to the empty hole for peg 6 with no pressure applied.  Step 24 to Chain, Jewelry Wire & Gemstones Earrings Jewelry Making Project

Step 24:  For our last loop, we don't need to remove the wire from your jig.  Just add peg 6 and wrap the wire around peg 6 as shown at right. 

Step 25 to Chain, Jewelry Wire & Gemstones Earrings Jewelry Making ProjectStep 25:  Remove the wire from your jig and using your flush cutter, cut the excess wire.  Using your bent chain nose pliers, close the final loop in your wire component.  At this point, the bottom wire component should appear as shown at left. 

Step 26 to Chain, Jewelry Wire & Gemstones Jewelry Making ProjectStep 26:  Now we are ready to connect the top and bottom wire components.  To do this, we first use our bent chain nose pliers and open the loop on one end of the bottom wire component, connect that loop to one of the bottom loops in the top wire component and again using our bent chain nose pliers, close that loop.  To connect the opposite side of the top and bottom wire components is slightly more difficult.  You will need to open the end loop on that end of the bottom wire component and open the end loop on the top wire component.  With both loops open, connect that side of the two components and then close both loops.  The two connected components should appear as shown at right. 

Step 27:  At this time, we need to set our gemstones in our low wall bezel findings.  Get your 10mm and 8mm low wall bezel findings (10mm is Item 3209 in gold-filled and item 3211 in sterling silver.  8mm is item 3210 in gold filled and item 3212 in sterling silver.  You can view our selection of gemstones here.)  Set both the 10mm and 8 mm gemstones following steps A through D shown below. 

Step 27A to Chain, Jewelry Wire & Gemstones Earrings Jewelry Making Project Step 27B to Chain, Jewelry Wire & Gemstones Earrings Jewelry Making Project Step 27C to Chain, Jewelry Wire & Gemstones Earrings Jewelry Making Project Step 27D to Chain, Jewelry Wire & Gemstones Earrings Jewelry Making Project Step 27E to Chain, Jewelry Wire & Gemstones Earrings Jewelry Making Project
Step A Step B Step C Step D Finished

Prior Page                    Page 5                    Next Page

Chain, Jewelry Wire & Gemstones Earrings Jewelry Making Project:  1     2     3    4     5    6     7     8     9     10     11 
View our Free Jewelry Making Instructions     Jewelry Making Skills     Jewelry Making Supplies     Jewelry Making Tools

Return to WigJig Jewelry Making Tools, Beads, Wire and Jewelry Supplies Home

See our selection jewelry making supplies, beads, wire and jewelry tools.

IMPORTANT PRINTING INSTRUCTIONS
All content on this web site is copyrighted by WigJigQuestions/Comments? 
WigJig is a registered trademark - Last modified: 07/11/2007