Making Jewelry with Half Drilled Pearl Beads -- Page 2

HOME   JEWELRY MAKING INSTRUCTIONS   WIGJIG UNIVERSITY   NEWSLETTER   GIFT IDEAS   WIGJIG STORE
VIEW OUR BEADS  BLING  BOOKS  CHAIN  FINDINGS  MISC  SUPPLIES  THREAD  JEWELRY TOOLS  WATCHES  WIRE

Making Jewelry with Half Drilled Pearl Beads:  1   2   3   4   5   View our Pearl Beads Kits!     View our 1/2 Drilled Pearl Beads
View our Free Jewelry Making Instructions     Jewelry Making Skills     Jewelry Making Supplies     Jewelry Making Tools

Step 1:  Assemble the components.  You will need two 1/2 drilled pearl beads in 6mm or 8mm size, one pair of the appropriate finding for setting the size beads you choose and a pair of ear clutches.  In the close-up picture below-right, you can view the finding so that you can see both the cup and the post.  For 6mm beads, a sterling silver finding is item 3289 and a gold-filled finding is item 3290.  For 8mm beads a sterling silver finding is item 3287 and a gold-filled finding is item 3288.  You can view our select of 1/2 drilled pearl beads from the link above-right. 

Step 1 to Making Jewelry with 1/2 Drilled Pearl Beads Step 1A to Making Jewelry with 1/2 Drilled Pearl Beads

Step 2: Using a nail file, or a jeweler's file, file the area around the hole in the bead.  The manufacturing process results in a small amount of the pearl coating on the bead accumulating around the hole in the bead.  You will want to file this area until it is smooth and flat with the rest of the surface of the bead.  This should take about 10 -20 seconds of filing. 

Step 2 to Making Jewelry with 1/2 Drilled Pearl BeadsStep 3:   Now place a WigJig tool face up on a table and set the long post from your finding into one of the holes in your WigJig.  As you can see at right, this holds the finding in position so that you will be able to easily apply glue to the shorter post within the cup.  The post itself has grooves that will help the glue to grip the metal.  Using GS-Hypo Tube Cement or similar glue, coat the short post and a small area around the post with glue.  Be careful that you don't apply too much glue, just enough to thoroughly coat the post and the area around the base of the post.  Step 3 to Making Jewelry with 1/2 Drilled Pearl BeadsTo spread the glue evenly you may want to rotate the finding with one finger as you apply the glue with the opposite hand. 

Step 4:   Slide your 1/2 drilled pearl bead onto the post.  Press down gently.  Allow to dry for about 30 minutes.  Leave the earring upright in your WigJig tool as the glue dries.  Step 4 to Making Jewelry with 1/2 Drilled Pearl Beads

Step 5:  The final step, after your glue has completely dried, is to add your butterfly style ear clutch.  Now your earring is ready to be worn. 

 

For those of you who make and sell jewelry, this is an excellent project where you can purchase the supplies to make these earrings for less than $5 and make a pair of earrings in less than a minute.  Our opinion is that these earrings should sell well at prices less than $10.  We believe that having a low priced item like these earrings can get shoppers to stop and view your merchandise and therefore will also help to sell your more expensive merchandise.  These earrings also make great presents!

Prior Page                    Page 2                    Next Page

Making Jewelry with Half Drilled Pearl Beads:  1   2   3   4   5   View our Pearl Beads Kits!     View our 1/2 Drilled Pearl Beads
View our Free Jewelry Making Instructions     Jewelry Making Skills     Jewelry Making Supplies     Jewelry Making Tools

Return to WigJig Jewelry Making Tools, Beads, Wire and Jewelry Supplies Home
See our selection jewelry making supplies, beads, wire and jewelry tools.

IMPORTANT PRINTING INSTRUCTIONS
All content on this web site is copyrighted by WigJigQuestions/Comments? 
WigJig is a registered trademark - Last modified: 06/17/2007